Pack 4 - 10x6 White Steel 2-Way Air Register (Duct Opening)

Replace your worn-out 10" × 6" louvered grille with a solid steel 2-way vent register. It mounts on walls and ceilings, fits straight over your existing duct opening, and puts 2-way airflow control at your fingertips. The classic white powder-coated finish blends with most wall colors and ceiling trim — no painting required for a standard replacement look.

This 10x6 2-way air vent cover is a direct, no-modification replacement for standard 10" × 6" supply duct openings in bedrooms, home offices, living rooms, kitchens, hallways, and common wall or ceiling supply runs.

Not every room calls for a designer slot diffuser. Sometimes you need a clean, durable, screw-mounted supply register that does its job without becoming the focus of the room. This Green Vent 2-way register is steel — not flimsy plastic — powder-coated white, and built for standard wall and ceiling duct openings.

The 2-way directional lever opens, closes, or fine-tunes supply airflow. Close it to block air from an unused guest room. Open it halfway for seasonal balancing. Direct air toward or away from furniture. It works especially well in bedrooms, home offices, basements, utility rooms, and rental properties where function and consistency matter.

The 4-pack is built for multi-room replacement projects, rental property upgrades, new construction finishing, and remodels where a consistent white register finish matters across several rooms.

IMPORTANT: Measure the hole in your wall or ceiling — do not measure your old vent cover.

This 10" × 6" 2-way air vent register fits a standard 10" × 6" duct opening (also listed as a 6" × 10" wall register or 6" × 10" supply vent cover).

• Duct opening size: 10" × 6" (this is what you measure)
• Overall face size: 11-3/4" × 7-3/4"
• Design note: The outer frame overlaps the duct opening on all four sides, covering small gaps or rough drywall edges for a finished look without patching.

Quick check:

1. Remove your existing vent cover from the wall or ceiling.
2. Measure the opening in the wall or ceiling — not the old cover's face.
3. If the opening is approximately 10" × 6", this register fits.

On the wall

Replaces dated beige, brown, or yellowed plastic registers in bedrooms, home offices, living rooms, kitchens, hallways, and common wall or ceiling supply runs. The steel body stands up to bumps from furniture, vacuums, and accidental impacts that would crack a plastic grille. The white powder-coated finish stays clean under daily HVAC airflow and temperature changes.

On the ceiling

A standard, low-profile option for ceiling supply vents in basements, garages, attics, utility spaces, and finished rooms. The white finish blends against white ceilings so the register does its job without drawing attention. Compatible with both forced-air heating and central air conditioning supply ducts.

• Solid Steel Construction: Heavy-gauge steel feels substantial and lasts longer than plastic registers. It will not crack, warp, or yellow like plastic alternatives.
• 2-Way Directional Lever: The built-in lever opens for full supply airflow, closes to block air from unused rooms, or stops anywhere in between for airflow balancing. Finger-operated — no tools required.
• White Powder-Coated Finish: Durable coating resists chipping and discoloring under daily temperature cycling. Blends with standard wall and ceiling trim. Paintable if you need a custom color match.
• Clean Screw-Mount Install: Pre-drilled mounting holes accept the included screws for a secure, rattle-resistant fit flush against the wall or ceiling surface.
• Wall & Ceiling Supply Register: Designed for sidewall and ceiling supply air use only. Not designed for floors, return air, outdoor use, or direct wet-area exposure.

No special tools required. This 10x6 2-way vent register mounts directly over your existing duct opening in a few simple steps.

1. Remove the old register or grille from the wall or ceiling opening.
2. Confirm the duct opening measures 10" × 6".
3. Place the Green Vent register over the opening — the face plate overlaps all four sides.
4. Secure with the included mounting screws through the pre-drilled holes.
5. Adjust the 2-way lever to your preferred airflow direction.

1. What size do I order — 10x6 or face size?

Order by duct opening size: 10" × 6". That is the hole in your wall or ceiling. The outer face measures 11-3/4" × 7-3/4" and overlaps the duct opening on all sides. Measure the duct hole before ordering, not your old cover's outer frame.

2. Steel register or aluminum linear slot diffuser — which should I choose?

Steel registers are a practical, budget-friendly choice for rentals, basements, utility rooms, and straightforward replacements. If you want a sleeker, modern look for main living spaces, a Green Vent aluminum linear slot diffuser is the designer-grade upgrade.

3. Can I install this on a floor?

No. This register is rated for wall and ceiling installation only. It is not load-bearing and is not designed for floor use. For floor duct openings, browse the floor register collection.

4. What does the 2-way lever do?

The built-in lever controls the louver position. Open fully for maximum supply airflow, close it to block air from an unused room, or stop it halfway for seasonal airflow balancing and directing air toward or away from a specific spot in the room.

5. Will this work as a return air vent?

No. This is a supply air register only. Return air openings need a dedicated return grille with a larger open face area to handle return air volume without restricting flow.

6. Is the white finish paintable?

Yes. Lightly sand the surface, apply a standard primer, and finish with spray paint if you want to match trim, accent walls, or landlord repaint work.

7. How loud is this register under normal airflow?

The steel louvers are designed to support smooth airflow and help reduce the rattling and whistling common in loose or cheap plastic registers. If you hear rattling, check that the mounting screws are secure and the register sits flush.

8. Can this be installed outdoors or in a bathroom?

No. This register is for indoor wall or ceiling use only. It is not rated for outdoor weather, direct moisture, or wet-area exposure.

• Want a modern aluminum upgrade for the same opening? See the 10x6 aluminum linear slot diffuser.
• Need a return air grille? Browse the air return grille collection.
• Browse all 2-way wall and ceiling registers in the 2-way air vent covers collection.
• Shop all vent options for a 10" × 6" opening in the 10x6 vent covers collection.
• Only need one register? See the 10x6 2-way air vent register single pack.